Saved

Blog · Card Storage & Protection

Pokémon Toploader Thickness Guide: 35pt, 55pt, 100pt and 130pt (2026)

For most Pokémon cards, including every standard Scarlet & Violet print and every WotC card from Base Set onwards, a 35pt toploader is the right choice. The "pt" stands for point, a unit equal to 1/1000 of an inch, and it describes how thick a card the holder is designed to protect. Use this guide to match your cards to the correct thickness and avoid the two most common mistakes: buying too tight (the card won't slide in cleanly) or too loose (it rattles and edges chip).

The only Pokémon cards that need a thicker holder are oversized metal promos from Ultra-Premium Collections released since 2021, and certain thick promotional cards. Everything else fits a standard 35pt.

Ultra PRO Pikachu TOPLOADER and PENNY SLEEVES Combo Pack 25 count
Pikachu TOPLOADER and PENNY SLEEVES Combo Pack (25-count) · $6.99 USD
On this page 6 sections
  1. What pt toploader for Pokémon cards: fit chart
  2. Choose by what you're protecting
  3. Mistakes that damage cards
  4. Magnetic one-touch holders: when to use them instead
  5. Gift angle: card protection for the collector in your life
  6. Frequently asked questions

What pt toploader for Pokémon cards: fit chart

The table below covers every card type you're likely to encounter in the Pokémon TCG.

Card type Thickness (approx.) Toploader to use Notes
Standard modern cards (SV, SWSH, Sun & Moon, XY) ~0.30–0.32 mm (≈11.8–12.6 pt) 35pt Fits all SV era cards including ex, full-art, and special illustration rares
WotC-era cards (Base Set through EX era) ~0.30–0.33 mm 35pt Same card stock weight as modern; standard 35pt fits cleanly
Standard promo cards (prerelease, event promos) ~0.30–0.33 mm 35pt Same stock as packs; no thicker holder needed
Thick-print promos (some older WOTC foils, jumbo-sized cards) ~0.35–0.50 mm 55pt Use if a 35pt feels snug when sliding in; never force a tight fit
Metal promos: Celebrations (2021), Arceus VSTAR UPC (2022) ~0.70–0.85 mm 100pt Per Ultra PRO product guidance; check individual listing specs against official Pokémon TCG product pages
Metal promos: Pokémon 151 UPC (2023), thick stamped metals ~0.90–1.10 mm 130pt See metal card toploader guide for each UPC release

One original data point: a 25-count pack of 35pt toploaders costs roughly $5–$7 from merchants observed on November 6, 2026, putting the per-toploader cost at $0.20–$0.28. That makes 35pt the most cost-effective single-card protection in the hobby, cheaper per card than most inner or outer sleeve options. The 200-count bulk pack at $35.99 (observed November 6, 2026) works out to about $0.18 per toploader, the best rate available without buying wholesale.

35pt Toploader 200 count with sleeves combo pack
35pt Toploader (200-count) with Sleeves COMBO Pack · $35.99 USD

Choose by what you're protecting

Standard and vintage cards (35pt)

Every Scarlet & Violet card, every Sword & Shield card, every Sun & Moon and XY card, and every WotC-era card from Base Set through the EX era measures between 0.30 mm and 0.33 mm thick. A 35pt toploader is designed for cards up to 35/1000 of an inch (0.889 mm) and gives your card enough room to slide in cleanly without rattling. Even raw Base Set holos, which collectors often assume need extra protection because of their age and value, are the same card stock as modern prints and fit standard 35pt holders comfortably.

A penny sleeve inside the toploader is the standard pairing. The sleeve adds a thin barrier between the card surface and the plastic, preventing micro-scratches during insertion and removal.

Thick promo cards (55pt)

Some older promotional cards, particularly thick-stamped WotC foils and certain stamped event promos, run slightly heavier than standard card stock. If you notice resistance when sliding a card into a 35pt holder, or if the top opening feels visibly narrow, step up to a 55pt. Never force a card in: forced insertion bends corners.

Jumbo-sized cards (the oversized promos included in some ETBs and boxes) are a different category entirely. Those require oversized toploader or sleeve solutions. See the jumbo card storage guide for sizing options.

Metal promo cards from Ultra-Premium Collections (100pt–130pt)

The Celebrations Ultra-Premium Collection (2021) introduced metal promos to the modern era, followed by the Arceus VSTAR UPC (2022) and the Pokémon 151 UPC (2023). These metal cards are significantly thicker than any printed card, ranging from roughly 0.70 mm to 1.10 mm depending on the specific product.

A 35pt toploader will not close over them. Use 100pt for the thinner metal promos and 130pt for the thicker 151 UPC metals. For detail on each UPC metal card, see the metal card toploader guide.

Ultra Pro Toploaders 25-count Pokemon

Ultra Pro Toploaders 25ct-Pokemon

$4.99 USD

Mistakes that damage cards

  • Forcing a card into an undersized toploader. The opening bends the top corners immediately. If there is resistance, go up a thickness.
  • Skipping the penny sleeve. Direct plastic-to-card contact scratches the surface during insertion. Always sleeve before toploading.
  • Stacking toploaders without dividers in a storage box. Cards shift and edges chip. Rubber-band groups of 25 or use a divider box.
  • Using a 100pt or 130pt toploader for a standard card. The card rattles inside and edges rub against the inner walls during any movement.
  • Buying non-UV toploader for high-value cards. Standard clear toploaders offer no UV protection. UV-blocking toploaders cost slightly more and are worth it for vintage holos or high-value rares stored near windows.
  • Sealing a toploader with tape directly on the card edge. Use team bags (resealable poly bags) over the toploader opening instead.

Magnetic one-touch holders: when to use them instead

Toploaders slide open from the top, which means a card can fall out if the holder is tilted. For high-value individual cards you plan to display rather than sort into boxes, a magnetic one-touch holder is a better fit.

The standard Pokémon TCG card (63.5 mm × 88.9 mm) fits a 35pt one-touch. The magnetic closure holds shut without tape, and UV protection is built into most models.

The trade-off: one-touch holders cost $5–$9 each versus roughly $0.20 for a toploader. Use toploaders for bulk storage and one-touches for your grail cards or display shelf.

One-Touch Edge Pokemon Poke Ball Magnetic Holder UV 35pt

One-Touch: Edge: Pokémon: Poké Ball Magnetic Holder UV 35pt

$5.99 USD

For a full side-by-side of toploaders versus one-touch magnetic holders, including which is better before grading submission, see the toploaders vs one-touch guide.

Ultra Pro ONE-TOUCH Edge Poke Ball Printed Magnetic Card Holder for Pokemon
Ultra PRO ONE-TOUCH Edge: Pokémon Poké Ball Printed Magnetic Card Holder · $8.99 USD

Gift angle: card protection for the collector in your life

A 25-count toploader pack with matching penny sleeves makes a practical stocking filler for any Pokémon TCG player or collector this Q4. Pair it with a couple of Scarlet and Violet ex tins and you have a gift that covers both the cards and the protection. For a broader list of gift ideas across all budgets, see the Pokémon holiday gift guide.

Frequently asked questions

What pt toploader do I need for Pokémon cards?

35pt fits every standard Pokémon TCG card, including WotC-era Base Set cards, modern Scarlet & Violet prints, and standard promo cards. Only metal promos from Ultra-Premium Collections need 100pt or 130pt holders.

Do WotC cards need a thicker toploader than modern cards?

No. WotC-era cards (Base Set through EX era) use the same card stock thickness as modern prints, approximately 0.30–0.33 mm, and fit standard 35pt toploaders. Age does not change the stock thickness.

Can I use a 55pt toploader for standard cards?

You can, but a standard card will rattle inside the extra space, and that movement chips edges over time. Use 35pt for standard cards; 55pt is for genuinely thicker promos where a 35pt feels tight.

What toploader fits the metal cards from Ultra-Premium Collections?

Use 100pt for most metal promos (Celebrations 2021, Arceus VSTAR 2022) and 130pt for the thicker metals in the Pokémon 151 UPC (2023). Check each listing's inner dimension spec before buying, as metal card thickness varies slightly by release.

Should I use a toploader or a magnetic one-touch for a card before grading?

PSA and CGC both accept cards in a penny sleeve inside a toploader. One-touch magnetic holders are fine for submission too, but remove the magnet before shipping: the case itself can be submitted, the magnet should not press against the card during transit. See your grader's current submission guidelines before mailing.

Browse toploader options and card protection accessories from independent shops at DexHaul's sleeves and binders collection. DexHaul is independent and not affiliated with The Pokémon Company or Ultra PRO.

Catch 'em all

Toploaders and card protection accessories from independent shops.